Vehicles
90 not categorized PORSCHE 356 C OIL SEALCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.N0138157 View/Change Diagram
$1.00
Make a selection T55100204 Oil seal installer, flywheel end. Specially manufactured to our specifications, these tools make it easy to properly install the rear crankshaft seal. They fully support, position and press the fragile oil seal into place without distortion. For all 356 engines.
$82.45
Make a selection 53901133 All 356/912 engines have a steel plug in the bottom of the engine case to drain the oil. This plug has metric tapered threads and no seal ring is needed. View/Change Diagram
$25.25
Make a selection 90012310630 Oil drain plug copper washer for Boxster. Measures 18x24mm. Oil drain plugs use soft metals such as aluminum or copper to create a good seal. In order to prevent an oil drip after oil drain, it is necessary to replace the gasket. For oil drain plug gaskets, see aluminum and copper gaskets. View/Change Diagram
From $1.00
Make a selection 91110112300 Known as: sealing ring oil duct crankcase 539. 01.001.10 / sealing ring / sealing ring rubber / sealing ring oil duct / sealing ring rubber for oil duct and oil cooler View/Change Diagram
$3.93
Make a selection 69533190300 We have a limited supply of new German oe axle flanges, brand new complete studs. A new flange will cure worn splines and a grooveed oil seal surface. Or, your original flange may be bent causing a wheel to wobble. View/Change Diagram
From $373.41
Make a selection 021101173 2 required View/Change Diagram
$5.46
Make a selection 00004306500 Also use (qty.) (1) 999 707 283 40 o-ring (1) 928 105 184 00 seal (1) 999 113 268 40 seal General Fitment944 1989-91944 1985-88 944 1982-85 968 1992-95 924 1986-88
$111.56
Make a selection 021119955 This is another one of those small sealing washers to insure that all of the cooling air is flowing over the engine and not out the open holes! order all of the other sealing washers at the same time like the spark plugs and the oil pressure switch grommet. View/Change Diagram
$5.25
Make a selection 022115315 Oil cap seal for the 912e and the 1.8 l equipped 914 made from 1974-76. Viton material. View/Change Diagram
$7.10
Make a selection 100103041TU Mahle 4.1 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.1:1 compression. - 106 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. Water channels and case must be machined to fit. Please add the following to your order: 2 qty. Base gaskets, part # FVD10303905zfd 2 qty. Head gaskets, part # FVD10303905zkd 1 qty. O- ring base set, part # FVD10303905or 1 qty. O- ring head set, part # FVD10303905oro *please note: horsepower and torque gains depend on the softwa...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09911 TURBO/GT2 2001-05
From $8,474.70
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 100505965 With front and rear steel fender flares including lights (front and rear head / tail and fog lights, blinkers), side skirts, installation hardware (all seals, gaskets, screws washers, nuts), cup mirrors and accessories. Without rear spoiler. General Fitment911 1970-73
$11,088.46
Make a selection 100103038TU997 Mahle 3.8 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets with 23 mm wrist pin. - slip fit, steel (st52) cylinders. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.4:1 compression. - 102 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. *please note: horsepower and torque gains depend on the software used, camshafts, crankshaft and other internal modifications. 700+ hp and torque can be achieved with use of these pistons and cylinders with a proper engine build and software. Contact your sales person for ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$14,654.60
Make a selection 10010303000TU Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders have extremely high thermal resistance and are nikasil coated to reduce wear and friction. We also have the piston rings (sealing and oil scrapers) pre-installed to ensure reliability. Each of our piston and cylinder kits are complete and ready for installation. Features: mahle forged 935 3.0 l turbo pistons mahle nikasil coated cylinders increased 7:1 compression = greater acceleration 95 mm pistons / 95 mm finned wr group 0 cylinders piston rings pre-installed piston pins and circlips are included complete set of 6 - ready for installation made in Germany we recommend the complete engine gas...(choose a part on the right to read more) General Fitment911 1970-73
From $6,197.50
Make a selection 91110717603 Replace your magnetic oil drain plug frequently to reduce engine wear and polishing of critical engine components. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. To complete the installation, please purchase a crush washer, part # 90012301120 sold individually. 1 necessary per car. View/Change Diagram
From $10.25
Make a selection 106084 There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more) General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05 911 1987-89
$899.99
Make a selection 91110700805 The oil pump is a critical component of the oil system and should not be overlooked on an engine rebuild or during engine maintenance. If the pump is starting to fail, you can experience no start issues, decreased oil pressure, higher engine temperatures, clanking noises coming from the lifters and valve train. This pump is high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. For a complete installation, we recommend replacing the lock tabs, (3 qty.) part # 99903900100 the smaller sealing rings, (2 qty.) part # 99970417250eq and the larger ring, (1 qty.) part # 99970417350eq the pump is sold individually. 1 necess...(choose a part on the right to read more) View/Change Diagram
From $1,150.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |